Centrifuge — Dewatering Model

Plant: — Scenario: — Generated: — Sprategy — Field Operations
SPRATEGY

Centrifuge Calculator

Decanter centrifuge — mass balance, G-force, polymer feed and cost
Dry solids
—
dry tons / day
Polymer
—
gal product / day
Cake produced
—
wet tons / day
G-force
—
× gravity at bowl wall
Cost per dry ton
—
polymer only
Parameters — open a section to adjust, close it when you're done
1

Sludge feed

—
›
Start here. Polymer demand, cake tonnage and centrifuge loading all follow from how much dry solid material is fed each day.
  • The feed rate is per centrifuge. Total flow is that figure multiplied by the number of machines running.
  • Feed solids swings the answer more than anything else. The same flow at 2% versus 4% solids is double the dry tonnage — and double the polymer.
  • Feed rate is also an operating lever: pushing more flow through the bowl shortens the time solids have to settle, so capture falls and cake gets wetter.
10GPM per centrifuge400
Read it off the feed pump flow meter. This is not total plant flow.
1machines6
How many are running at the same time, not how many are installed.
1hours24
Hours the feed pump is actually on. Leave out start-up and flush time.
0.5%% by weight10%
Ask for the lab total-solids result on the centrifuge feed. It varies day to day.
1.00sg1.10
Thin sludge is close to water, 1.00 to 1.03.
Show the math — how feed becomes dry tons
—
2

Centrifuge settings and performance

—
›
What the operators set, and what the machine gives back. Bowl speed and bowl diameter fix the G-force — that part is physics and is calculated here. Cake solids and capture are results: enter what the plant measures, then change them to see what a better or worse day does to tonnage, centrate and cost.
  • Bowl speed up → more G → drier cake and cleaner centrate, at the cost of power and wear.
  • Differential down → solids stay in the bowl longer → drier cake, higher torque. Too low and the bowl plugs or solids spill into the centrate.
  • Differential up → solids leave faster → wetter cake, more solids-handling capacity.
Differential is recorded on the report but does not drive the numbers: how much cake dryness you gain per RPM is specific to each machine and sludge, and only the operators' own trend data can tell you that.
10inches, inside diameter44
From the nameplate or O&M manual. Fixed for the machine.
800RPM4,000
Shown on the control panel. G-force rises with the square of speed.
1RPM, scroll vs bowl30
Recorded for the report only. Many machines adjust it automatically to hold a torque setpoint.
10%% solids in cake40%
Lab total solids on the discharged cake. Drier cake means fewer wet tons to move.
70%% captured99.5%
Share of feed solids ending up in the cake. The rest leaves in the centrate.
Show the math — G-force, cake and centrate
—
3

Polymer and cost

—
›
Cost per dry ton is the number that matters, not price per gallon or per pound. A product at a lower price but lower active content needs more weight to do the same job.
  • Dose is entered as active polymer per dry ton, so two products can be compared fairly. The product weight is worked out from the active content.
  • Liquid emulsion is bought by the gallon or tote but dosed by weight — the product's specific gravity links the two.
  • More polymer helps capture and dryness only up to a point. Past the optimum it is wasted money and can make the cake slimy.
1lb active / dry ton40
Back-calculate it from the plant's real usage if you can — see the guide.
10%% active100%
Emulsions are typically 25 to 50%. Use the figure on the certificate of analysis.
$0.25$ per lb$6.00
—
1.00sg of neat product1.15
—
400lb of product per tote2,600
—
0.1%% product in solution2%
Neat emulsion is diluted with water before injection. That water ends up in the centrate.
50days365
Days the centrifuge actually runs. Allow for maintenance and shutdowns.
$0$ per wet ton$150
Optional. Hauling or disposal cost, to put a dollar value on drier cake. Leave at 0 to ignore.
Show the math — polymer demand, pump rates and cost
—
4

Report details

optional — appears on the printout
›
Process flow
Sludge in
—
—
→
—
Dry solids
—
dry tons / day
→
+ polymer
Centrifuge
—
—
→
—
Cake out
—
—
↳
centrate
Centrate return
—
gal / day
Daily output
Dry solids processed
—
dry tons / day
—
Polymer consumed
—
lb product / day
—
Dewatered cake
—
wet tons / day
—
Centrate
—
gal / day
—
Polymer feed — what the operator sets and what gets ordered
Neat polymer pump
—
gal / hr per centrifuge
—
Diluted solution
—
GPM per centrifuge
—
Product per dry ton
—
lb product / dry ton
—
One tote lasts
—
operating days
—
Performance checks
G-force
—
—
× gravity at the bowl wall
Typical for dewatering: 1,500 G or more
Cake solids
—
—
% solids in dewatered cake
Generic target: 18% or better
Solids capture
—
—
% of solids ending in cake
Typical target: 95% or better
What changed — compare against a held baseline

Scenario comparison

Set the plant's current operation, hold it, then move one variable at a time.

MeasureBaselineNowChange
Daily mass balance
Streamlb / daytons / daygal / dayNote
Annual summary
Dry tons per year
—
dry tons
—
Polymer per year
—
gal product
—
Annual polymer cost
—
USD per year
—
Cake per year
—
wet tons
—
These are engineering estimates. The default values are generic placeholders, not this plant's data. Confirm measured feed solids, actual run hours, bowl size and speed, polymer active content and real polymer usage before using these figures for purchasing, bidding or design.

Centrifuge guide

What a decanter centrifuge does

A decanter is a horizontal bowl spinning at a few thousand RPM. Sludge is fed into the middle; the spin throws the heavier solids against the bowl wall, where they pack into a layer. A screw conveyor (the scroll) inside the bowl turns slightly slower or faster than the bowl and drags that layer up a sloped section (the beach) and out one end as cake. The clarified water (centrate) overflows weirs at the other end.

Polymer is injected into the feed just ahead of or inside the machine. It binds fine particles into larger, stronger flocs that settle fast and survive the shear inside the bowl. Without it most fine solids would leave with the centrate.

The operating levers and what each one does

LeverRaise it and…The trade-off
Bowl speedMore G-force. Drier cake, cleaner centrate.More power, more wear, more floc shear.
Differential speedSolids leave faster. More solids capacity, lower torque.Wetter cake. Lower it for drier cake — until torque trips or solids carry over.
Pond depth (weir setting)More settling volume. Cleaner centrate.Shorter dry beach, so wetter cake. Shallow pond does the opposite.
Feed rateMore throughput per hour.Less time to settle: capture drops, cake gets wetter, polymer per ton tends to rise.
Polymer doseBetter capture and dryness up to the optimum.Past the optimum: wasted cost, slimy cake, foamy centrate.
Make-down strengthLess dilution water into the machine.Too strong and the polymer does not fully uncoil or mix; too weak adds hydraulic load.

Change one lever at a time and wait for the machine to settle before judging the result — usually 15 to 30 minutes.

G-force

G = 1.118 × 10⁻⁶ × RPM² × bowl radius (mm) bowl radius (mm) = bowl diameter (in) × 25.4 ÷ 2

G rises with the square of speed: a 10% speed increase is about 21% more G. Dewatering decanters commonly run somewhere between 1,500 and 3,500 G.

Dry tons — the unit everything runs on

dry lb/day = flow (GPM) × hours × 60 × 8.34 × specific gravity × solids% dry tons/day = dry lb/day ÷ 2000

The 8.34 is the weight of one gallon of water in pounds. Polymer demand, cake tonnage and cost are all per dry ton.

Why cake solids matters

wet cake (tons/day) = dry tons captured ÷ (cake solids% ÷ 100)

At 18% solids each dry ton is 5.6 wet tons to move. At 22% it is 4.5. Every wet ton avoided is one that does not have to be loaded, hauled, spread or stored.

Capture rate and centrate quality

Solids that are not captured leave in the centrate and go back to the front of the process, where they have to be treated again.

centrate TSS (mg/L) ≈ lost solids (lb) ÷ centrate (gal) × 119,826 recycle multiplier ≈ 1 ÷ capture rate

Cloudy or grey centrate is the first visible sign that capture is slipping. Operators usually judge it by eye at the sample tap long before a lab result comes back.

Liquid polymer: pounds, gallons and totes

lb product per dry ton = active dose ÷ (active% ÷ 100) lb per gallon = 8.34 × polymer specific gravity gallons per day = lb product per day ÷ lb per gallon days per tote = tote net weight ÷ lb product per day

A 2,300 lb tote at 1.04 specific gravity holds about 265 gallons. If the price is quoted per gallon, divide by lb per gallon to compare against a per-pound quote.

Back-calculating the plant's real dose

The most reliable dose figure comes from what the plant actually used, not from a book range.

lb product used = totes used × tote net weight lb product / dry ton = lb product used ÷ dry tons processed active dose = lb product / dry ton × (active% ÷ 100)

Ask for totes used and dry tons (or feed gallons and average feed solids) over the same period, then adjust the dose slider until "one tote lasts" matches what the operators tell you.

Common troubleshooting

Handling liquid emulsion polymer

Questions worth asking the operators

Jar tests versus the machine

A jar test screens polymers and gives a starting dose, but it cannot reproduce the shear inside a spinning bowl. A polymer that looks good in a jar can fall apart in the centrifuge. Final proof is always a trial on the machine itself.